entertainment-center3, Meble PROJEKTY

[ Pobierz całość w formacie PDF ]
E
ntertainment Center
If you have always wanted a good-looking entertainment center to house your stereo,
television, records, CDs, and books, here’s the answer. You can build it for much less
than you would pay in a furniture store. This one is built in three individual sections so
that it can be moved easily. We sponge-painted ours and are very happy with the finished
project.
Materials
The materials specified are
enough to make two outer
cabinets and one center
cabinet.
 
27 linear feet of 1 x 2
pine
 
150 linear feet of 1 x 4
pine
 
36 linear feet of 2 x 4
pine
 
3 linear feet of 1 x 8
pine
 
17 linear feet of 5-1/2"
crown molding
 
13 linear feet of 3"
crown molding
 
24 linear feet of 3/4"
rope molding
 
7-1/2 (4' x 8') sheets of
3/4" plywood
 
4-1/2 sheets of (4 x 8
feet) 1/4" plywood
1
Hardware
 
325 3/4" wire brads
 
250 1" (2d) finishing nails
 
20
1-1/4" (3d) finishing nails
 
350 1-1/2" screws
 
36
2" screws
 
24
2-1/2" screws
 
24
3" screws
 
16
cabinet door hinges
 
8
door pulls
 
8
magnetic catches
Special Tools and Techniques
 
Router
 
Pipe clamps or long bar clamps
 
Staple gun
 
Miters
Cutting List
Code Description
Qty Materials
Dimensions
A
Sides
2
3/4" plywood
23-1/4” x 82-1/2”
B
Top/Bottom
2
3/4" plywood
23-1/4” x 37-1/2”
C
Shelf
4
3/4" plywood
23-1/4" x 36”
D
Vertical Trim
2
1 x 4 pine
84” long
E
Horizontal Trim
2
1 x 4 pine
30-1/2" long
F
Wide Horizontal Trim
1
1 x 8 pine
30-1/2" long
G
Molding Trim
1
3/4" rope molding
30-1/2" long
H
Top/Bottom Door Trim 8
1 x 4 pine
15" long
I
Wide Side Door Trim
4
1 x 4 pine
38" long
J
Narrow Side Door Trim 4
1 x 2 pine
38” long
K
Door Panel
4
1/4" plywood
14-3/4” x 34-1/2”
2
L
Support Blocks
2
1 x 2 pine
4" long
M
Base Sides
2
2 x 4 pine
18-1/2" long
N
Base Front/Back
2
2 x 4 pine
35" long
O
Base Supports
4
2 x 4 pine
12" long
P
Back
1
1/4" plywood
37-1/2" x 84"
Q
Sides
4
3/4" plywood
16” x 78-1/2"
R
Top/Bottom
4
3/4" plywood
16” x 30"
S
Shelf
10 3/4" plywood
16” x 28-1/2"
T
Vertical Trim
4
1 x 4 pine
80" long
U
Horizontal Trim
8
1 x 4 pine
23" long
V
Molding Trim
2
3/4" rope molding
23" long
W
Top/Bottom Door Trim 8
1 x 4 pine
11-1/2" long
X
Wide Side Door Trim
4
1 x 4 pine
32-1/2" long
Y
Narrow Side Door Trim 4
1 x 2 pine
32-1/2” long
Z
Door Panel
4
1/4" plywood
11-1/4" x 29"
AA
Support Blocks
8
1 x 2 pine
4" long
BB
Base Sides
4
2 x 4 pine
11" long
CC
Base Front/Back
4
2 x 4 pine
28" long
DD
Base Supports
8
2 x 4 pine
7-1/2” long
EE
Back
2
¼” plywood
30” x 80”
FF
Top Molding
5-1/2” crown molding
Cut to fit
GG
Rope Molding
¾” rope molding
Cut to fit
HH
Bottom Molding
3” crown molding
Cut to fit
Constructing the Center Cabinet
1.
Cut two sides (A) from 3/4-inch plywood, each measuring 23-1/4 x 82-1/2inches.
2.
Cut two top/bottoms (B) from 3/4-inch plywood, each measuring 23-1/4 x 37-1/2 inches.
3.
Place the two sides (A) on edge on a level surface, 36 inches apart. Fit the top/bottoms (B)
over the ends of the sides (A) to form a rectangle, measuring 37-1/2 x 84 inches, as shown
in
Figure 1
. Apply glue to the meeting surfaces and screw through the top/bottoms (B)
3
into the edges of the sides (A). Use 1-1/2-inch screws spaced about every 5 inches.
Figure 1
4.
Cut four shelves (C)
from 3/4-inch
plywood, each
measuring 23-1/4 x
36 inches.
5.
Place the first shelf
(C) 2 inches below
the top (B). Screw
through the sides (A)
into the edges of the
shelf (C), as shown
in
Figure 2
. Use
1-1/2-inch screws spaced about every 5 inches.
6.
Repeat the procedure in Step 5 to attach the second shelf (C) 29-1/8 inches below the first
one.
7.
Attach the third shelf (C) 5 inches below the second one.
8.
Attach the fourth shelf (C) 2 inches above the bottom (B).
Figure 2
Adding the Trim to the Center Cabinet
1.
Cut two vertical trims (D) from 1 x 4 pine each measuring 84 inches long.
4
2.
Apply glue to the meeting surfaces and screw one vertical trim (D) to the edge of one side
(A), as shown in
Figure 3
. Use 1-1/2-inch screws spaced about every 5 inches.
3.
Repeat Step 3
to attach the
remaining
vertical trim (D)
to the opposite
side (A).
4.
Cut two
horizontal trims
(E) from 1 x 4
pine each
measuring 30-
1/2 inches long.
5.
Apply glue to the plywood edges and attach one horizontal trim (E) over the edges of the
top (B) and the first shelf (C), as shown in
Figure 4
. Screw through the horizontal trim (E)
into the edges of the top (B) and shelf (C) using 1-1/2-inch screws about every six inches.
6.
Repeat Step 5 to attach the second horizontal trim (E) to the third shelf (C) and the bottom
(B).
Figure 4
7.
Cut one wide horizontal trim (F) from 1 x 8 pine, measuring 30-1/2 inches long.
8.
Attach the wide horizontal trim (F) flush with the upper surface of the third shelf (C).
Apply glue to the plywood edge, and screw through the wide horizontal trim (F) into the
5
[ Pobierz całość w formacie PDF ]

  • zanotowane.pl
  • doc.pisz.pl
  • pdf.pisz.pl
  • materaceopole.pev.pl






  • Formularz

    POst

    Post*

    **Add some explanations if needed