Fanuc-3x 3xx-Users manual 2 EN, MIBM, Fanuc
[ Pobierz całość w formacie PDF ]
FANUC Series 30*/300*/300*s-MODEL A
FANUC Series 31*/310*/310*s-MODEL A5
FANUC Series 31*/310*/310*s-MODEL A
FANUC Series 32*/320*/320*s-MODEL A
For Lathe System
USER’S MANUAL
B-63944EN-1/02
•
No part of this manual may be reproduced in any form.
•
All specifications and designs are subject to change without notice.
The export of this product is subject to the authorization of the government of the country
from where the product is exported.
In this manual we have tried as much as possible to describe all the various matters.
However, we cannot describe all the matters which must not be done, or which cannot be
done, because there are so many possibilities.
Therefore, matters which are not especially described as possible in this manual should be
regarded as ”impossible”.
This manual contains the program names or device names of other companies, some of
which are registered trademarks of respective owners. However, these names are not
followed by
or
in the main body.
B-63944EN-1/02
SAFETY PRECAUTIONS
SAFETY PRECAUTIONS
This section describes the safety precautions related to the use of CNC
units.
It is essential that these precautions be observed by users to ensure the
safe operation of machines equipped with a CNC unit (all descriptions
in this section assume this configuration). Note that some precautions
are related only to specific functions, and thus may not be applicable
to certain CNC units.
Users must also observe the safety precautions related to the machine,
as described in the relevant manual supplied by the machine tool
builder. Before attempting to operate the machine or create a program
to control the operation of the machine, the operator must become
fully familiar with the contents of this manual and relevant manual
supplied by the machine tool builder.
CONTENTS
1.1 DEFINITION OF WARNING, CAUTION, AND NOTE ........s-2
1.2 GENERAL WARNINGS AND CAUTIONS ...........................s-3
1.3 WARNINGS AND CAUTIONS RELATED TO
PROGRAMMING.....................................................................s-6
1.4 WARNINGS AND CAUTIONS RELATED TO HANDLING s-9
1.5 WARNINGS RELATED TO DAILY MAINTENANCE.......s-12
s-1
SAFETY PRECAUTIONS
B-63944EN-2/02
1.1
DEFINITION OF WARNING, CAUTION, AND NOTE
This manual includes safety precautions for protecting the user and
preventing damage to the machine. Precautions are classified into
Warning
and
Caution
according to their bearing on safety. Also,
supplementary information is described as a
Note
. Read the
Warning
,
Caution
, and
Note
thoroughly before attempting to use
the machine.
WARNING
Applied when there is a danger of the user being
injured or when there is a danger of both the user
being injured and the equipment being damaged if
the approved procedure is not observed.
CAUTION
Applied when there is a danger of the equipment
being damaged, if the approved procedure is not
observed.
NOTE
The Note is used to indicate supplementary
information other than Warning and Caution.
• Read this manual carefully, and store it in a safe place.
s-2
B-63944EN-2/02
SAFETY PRECAUTIONS
1.2
GENERAL WARNINGS AND CAUTIONS
WARNING
1 Never attempt to machine a workpiece without first
checking the operation of the machine. Before
starting a production run, ensure that the machine
is operating correctly by performing a trial run
using, for example, the single block, feedrate
override, or machine lock function or by operating
the machine with neither a tool nor workpiece
mounted. Failure to confirm the correct operation
of the machine may result in the machine behaving
unexpectedly, possibly causing damage to the
workpiece and/or machine itself, or injury to the
user.
2 Before operating the machine, thoroughly check
the entered data.
Operating the machine with incorrectly specified
data may result in the machine behaving
unexpectedly, possibly causing damage to the
workpiece and/or machine itself, or injury to the
user.
3 Ensure that the specified feedrate is appropriate
for the intended operation. Generally, for each
machine, there is a maximum allowable feedrate.
The appropriate feedrate varies with the intended
operation. Refer to the manual provided with the
machine to determine the maximum allowable
feedrate.
If a machine is run at other than the correct speed,
it may behave unexpectedly, possibly causing
damage to the workpiece and/or machine itself, or
injury to the user.
4 When using a tool compensation function,
thoroughly check the direction and amount of
compensation.
Operating the machine with incorrectly specified
data may result in the machine behaving
unexpectedly, possibly causing damage to the
workpiece and/or machine itself, or injury to the
user.
s-3
[ Pobierz całość w formacie PDF ]