exj 22, JEEP Manuals, Electronic Service Manual (jeep cherokee xj do 2000)
[ Pobierz całość w formacie PDF ]
XJ
TIRES AND WHEELS
22 - 1
TIRES AND WHEELS
TABLE OF CONTENTS
page
page
1
7
TIRES
TABLE OF CONTENTS
page
page
DESCRIPTION AND OPERATION
DIAGNOSIS AND TESTING
SERVICE PROCEDURES
CLEANING AND INSPECTION
SPECIFICATIONS
DESCRIPTION AND OPERATION
TIRE IDENTIFICATION
Tire type, size, aspect ratio and speed rating are
encoded in the letters and numbers imprinted on the
side wall of the tire. Refer to the chart to decipher
the tire identification code (Fig. 1).
Performance tires have a speed rating letter after
the aspect ratio number.
TIRES
DESCRIPTION
Tires are designed and engineered for each specific
vehicle. They provide the best overall performance
for normal operation. The ride and handling charac-
teristics match the vehicle’s requirements. With
proper care they will give excellent reliability, trac-
tion, skid resistance, and tread life.
Driving habits have more effect on tire life than
any other factor. Careful drivers will obtain in most
cases, much greater mileage than severe use or care-
less drivers. A few of the driving habits which will
shorten the life of any tire are:
²
LETTER
SPEED RATING
S
180 km/h (112 mph)
T
190 km/h (118 mph)
U
200 km/h (124 mph)
H
210 km/h (130 mph)
V
240 km/h (149 mph)
W
270 km/h (168 mph)
Rapid acceleration
Y
300 km/h (186 mph)
²
Severe brake applications
²
High speed driving
²
Excessive speeds on turns
The speed rating is not always printed on the tire
sidewall.
Striking curbs and other obstacles
Radial-ply tires are more prone to irregular tread
wear. It is important to follow the tire rotation inter-
val shown in the section on Tire Rotation. This will
help to achieve a greater tread life.
²
 22 - 2
TIRES AND WHEELS
XJ
DESCRIPTION AND OPERATION (Continued)
SPARE TIRE–TEMPORARY
DESCRIPTION
The temporary spare tire is designed for emer-
gency use only. The original tire should be repaired
or replaced at the first opportunity, then reinstalled.
Do not exceed speeds of 50 M. P. H. when using the
temporary spare tire. Refer to Owner’s Manual for
complete details.
TIRE INFLATION PRESSURES
Under inflation will cause rapid shoulder wear, tire
flexing, and possible tire failure (Fig. 2).
Fig. 1 Tire Identification
TIRE CHAINS
Tire snow chains may be used on
certain
models.
Refer to the Owner’s Manual for more information.
Fig. 2 Under Inflation Wear
1 – THIN TIRE THREAD AREAS
RADIAL-PLY TIRES
Over inflation will cause rapid center wear and
loss of the tire’s ability to cushion shocks (Fig. 3).
DESCRIPTION
Radial-ply tires improve handling, tread life and
ride quality, and decrease rolling resistance.
Radial-ply tires must always be used in sets of
four. Under no circumstances should they be used on
the front only. They may be mixed with temporary
spare tires when necessary. A maximum speed of 50
MPH is recommended while a temporary spare is in
use.
Radial-ply tires have the same load-carrying capac-
ity as other types of tires of the same size. They also
use the same recommended inflation pressures.
The use of oversized tires, either in the front or
rear of the vehicle, can cause vehicle drive train fail-
ure. This could also cause inaccurate wheel speed
signals when the vehicle is equipped with Anti-Lock
Brakes.
The use of tires from different manufactures on the
same vehicle is NOT recommended. The proper tire
pressure should be maintained on all four tires.
Fig. 3 Over Inflation Wear
1 – THIN TIRE THREAD AREA
Improper inflation can cause:
²
Uneven wear patterns
 XJ
TIRES AND WHEELS
22 - 3
DESCRIPTION AND OPERATION (Continued)
²
Reduced tread life
²
Handling
²
Reduced fuel economy
²
Durability
²
Unsatisfactory ride
²
Tread life
Vehicle drift
For proper tire pressure specification refer to the
Tire Inflation Pressure Chart provided with the vehi-
cle.
Tire pressures have been chosen to provide safe
operation, vehicle stability, and a smooth ride. Tire
pressure should be checked cold once a month. The
spare tire pressure should be check at least twice
annually. Tire pressure decreases as the ambient
temperature drops. Check tire pressure frequently
when ambient temperature varies widely.
Inflation pressures specified on the placards are
cold inflation pressure. The vehicle must sit for at
least 3 hours to obtain the correct cold inflation pres-
sure reading. Or driven less than one mile after sit-
ting for 3 hours. Tire inflation pressures may
increase from 2 to 6 pounds per square inch (psi)
during operation, due to increased tire temperature.
²
²
Traction
²
Rolling resistance
Speed capability
It is recommended that tires equivalent to the orig-
inal equipment tires be used when replacement is
needed.
Failure to use equivalent replacement tires may
adversely affect the safety and handling of the vehi-
cle.
The use of oversize tires may cause interference
with vehicle components. Under extremes of suspen-
sion and steering travel, interference with vehicle
components may cause tire damage.
²
WARNING: FAILURE TO EQUIP THE VEHICLE WITH
TIRES HAVING ADEQUATE SPEED CAPABILITY
CAN RESULT IN SUDDEN TIRE FAILURE.
WARNING: OVER OR UNDER INFLATED TIRES
CAN AFFECT VEHICLE HANDLING AND TREAD
WEAR. THIS MAY CAUSE THE TIRE TO FAIL SUD-
DENLY,
DIAGNOSIS AND TESTING
PRESSURE GAUGES
A quality air pressure gauge is recommended to
check tire pressure. After checking the air pressure,
replace valve cap finger tight.
RESULTING
IN
LOSS
OF
VEHICLE
CON-
TROL.
TIRE PRESSURE FOR HIGH SPEED
TREAD WEAR INDICATORS
Tread wear indicators are molded into the bottom
of the tread grooves. When tread depth is 1.6 mm
(1/16 in.), the tread wear indicators will appear as a
13 mm (1/2 in.) band (Fig. 4).
Tire replacement is necessary when indicators
appear in two or more grooves or if localized balding
occurs.
DESCRIPTION
Where speed limits allow the vehicle to be driven
at high speeds, correct tire inflation pressure is very
important. For speeds up to and including 120 km/h
(75 mph), tires must be inflated to the pressures
shown on the tire placard. For continuous speeds in
excess of 120 km/h (75 mph), tires must be inflated
to the maximum pressure specified on the tire side-
wall.
Vehicles loaded to the maximum capacity should
not be driven at continuous speeds above 75 mph
(120 km/h).
For emergency vehicles that are driven at speeds
over 90 mph (144 km/h), special high speed tires
must be used. Consult tire manufacturer for correct
inflation pressure recommendations.
TIRE WEAR PATTERNS
Under inflation will cause wear on the shoulders of
tire. Over inflation will cause wear at the center of
tire.
Excessive camber causes the tire to run at an
angle to the road. One side of tread is then worn
more than the other (Fig. 5).
Excessive toe-in or toe-out causes wear on the
tread edges and a feathered effect across the tread
(Fig. 5).
REPLACEMENT TIRES
TIRE NOISE OR VIBRATION
Radial-ply
DESCRIPTION
The original equipment tires provide a proper bal-
ance of many characteristics such as:
²
tires
are
sensitive
to
force
impulses
caused
by
improper
mounting,
vibration,
wheel
defects, or possibly tire imbalance.
To find out if tires are causing the noise or vibra-
tion, drive the vehicle over a smooth road at varying
Ride
²
Noise
 22 - 4
TIRES AND WHEELS
XJ
DIAGNOSIS AND TESTING (Continued)
patterns. These effects can be reduced by rotating
the tires at regular intervals. The benefits of tire
rotation are:
²
Increase tread life
²
Maintain traction levels
A smooth, quiet ride
The suggested method of tire rotation is (Fig. 6).
Other rotation methods can be used, but they will
not provide all the tire longevity benefits.
²
Fig. 4 Tread Wear Indicators
1 – THREAD ACCEPTABLE
2 – THREAD UNACCEPTABLE
3 – WEAR INDICATOR
Fig. 6 Tire Rotation Pattern
MATCH MOUNTING
Tires and wheels are currently match mounted at
the factory. Match mounting is a technique used to
reduce runout in the wheel/tire assembly. This means
that the high spot of the tire is aligned with the low
spot on the wheel rim. The high spot on the tire is
marked with a paint mark or a bright colored adhe-
sive label on the outboard sidewall. The low spot on
the rim is identified with a label on the outside of the
rim and a dot on the inside of the rim. If the outside
label has been removed the tire will have to be
removed to locate the dot on the inside of the rim.
speeds. Note the noise level during acceleration,
deceleration and slight left and right steering inputs.
SERVICE PROCEDURES
ROTATION
Tires on the front and rear operate at different
loads and perform different steering, driving, and
braking functions. For these reasons they wear at
unequal rates and tend to develop irregular wear
Fig. 5 Tire Wear Patterns
 XJ
TIRES AND WHEELS
22 - 5
SERVICE PROCEDURES (Continued)
Before dismounting a tire from its wheel, a refer-
ence mark should be placed on the tire at the valve
stem location. This reference will ensure that it is
remounted in the original position on the wheel.
(1) Use a dial indicator to locate the high spot of
the tire on the center tread rib (Fig. 7). Record the
indicator reading and mark the high spot on the tire.
Place a mark on the tire at the valve stem location
(Fig. 8).
(2) Break
down
the
tire
and
remount
it
180
degrees on the rim (Fig. 9).
Fig. 7 Dial Indicator
Fig. 9 Remount Tire 180 Degrees
1 – VALVE STEM
2 – REFERENCE MARK
(3) Measure the total runout again and mark the
tire to indicate the high spot.
(4) If runout is still excessive use the following
procedures.
(a) If the high spot is within 101.6 mm (4.0 in.)
of the first spot and is still excessive, replace the
tire.
(b) If the high spot is within 101.6 mm (4.0 in.)
of the first spot on the wheel, the wheel may be out
of specifications. Refer to Wheel and Tire Runout.
(c) If the high spot is NOT within 101.6 mm (4.0
in.) of either high spot, draw an arrow on the tread
from second high spot to first. Break down the tire
and remount it 90 degrees on rim in that direction
(Fig. 10). This procedure will normally reduce the
runout to an acceptable amount.
REPAIRING LEAKS
For proper repairing, a radial tire must be removed
from the wheel. Repairs should only be made if the
defect, or puncture, is in the tread area (Fig. 11). The
tire should be replaced if the puncture is located in
the sidewall.
Fig. 8 First Measurement On Tire
1 – REFERENCE MARK
2 –
1ST MEASUREMENT
HIGH SPOT MARK TIRE AND RIM
3 – WHEEL
4 – VALVE STEM
Â
[ Pobierz całość w formacie PDF ]